Stretch Fabric Petal Flush Mount

A closer fit for your
everyday comfort.

A flush mount ceiling light with a pleated stretch-fabric shade shaped into overlapping petal segments — the fabric pulls and gathers at the center, creating natural tension folds across the surface that catch light differently at different angles. The center cap is turned solid walnut with a brass-tone hardware fastener — a small material detail visible from below that keeps the fixture grounded in warm, furniture-grade materials rather than anonymous white plastic. At H15 cm the profile sits close to the ceiling and works in standard 2.4 m (8 ft) rooms without any drop. Integrated LED panel included — no bulb required. Three diameters: Ø40 cm (22W), Ø50 cm (32W), and Ø60 cm (48W). Integrated LED panel — no bulb required or replaceable The LED light source is an SMD panel built into the fixture. It ships pre-installed — no separate bulb purchase is needed. Because the LED is integrated, it cannot be replaced by the user when it reaches end of life. Rated LED lifespan is typically 25,000+ hours under normal use conditions. Hardwired ceiling install — flush mount This fixture hardwires directly to the ceiling junction box. It is not plug-in. A licensed electrician is recommended. Turn off power at the breaker before installation. Confirm your ceiling box is positioned at the correct location — flush mount fixtures cannot be repositioned after hardwiring. Features Pleated stretch fabric Stretch fabric pulled into overlapping petal segments — the material gathers at the center and fans outward, creating natural tension folds that shift in appearance under different light angles and times of day. Integrated LED · no bulb SMD LED panel ships pre-installed in the fixture — no bulb to source, install, or replace. Plug in power at the breaker after installation and it is ready. Solid walnut center · H15 cm A turned walnut cap with a brass-tone fastener closes the center of the shade — visible from below as a warm material detail. At H15 cm, the profile stays close to the ceiling and suits standard room heights. Select Your Size Small — Ø40 cm (22W) Medium — Ø50 cm (32W) Large — Ø60 cm (48W) Small — Ø40 × H15 cm · 22W Diameter: 40 cm (15.7″) · Height: 15 cm (5.9″) · Flush mount — no drop Light source: integrated LED panel (included) · 22W Suits: 10–13 m² rooms · bedroom · study · hallway · bathroom (confirm IP rating). Size at a Glance Size Diameter × Height Wattage Room coverage Best for Small Ø40 × H15 cm15.7″ × 5.9″ 22W ~10–13 m²108–140 sq ft Bedroom, study, hallway, compact living room Medium Ø50 × H15 cm19.7″ × 5.9″ 32W ~13–16 m²140–172 sq ft Bedroom, dining area, living room, open study Large Ø60 × H15 cm23.6″ × 5.9″ 48W ~16–18 m²172–194 sq ft Living room, dining room, primary bedroom, open-plan space Construction Stretch fabric shade · solid walnut center cap · brass-tone hardware · metal frame The shade is constructed from stretch fabric pulled over a metal petal-segment frame. Each segment fans outward from the center, and the tension in the fabric creates natural gather lines across the surface — not printed or embossed, but physically formed by how the fabric sits under tension. The center convergence point is capped with a solid walnut turned disc, finished with a small brass-tone fastener that closes the assembly from below. The overall color — off-white stretch fabric against walnut brown — stays within the warm neutral register without introducing any contrast color. The metal hardware frame mounts flush to the ceiling junction box. Light Source Integrated SMD LED panel · included · 22W / 32W / 48W An SMD (surface-mount device) LED panel is pre-installed inside the fixture and ships ready to use (22W for Ø40 cm, 32W for Ø50 cm, and 48W for Ø60 cm). The panel diffuses light evenly across the stretch fabric from behind, illuminating the gather folds from within. Because the LED is integrated into the fixture body, there is no socket and no user-replaceable bulb — the panel cannot be swapped out at end of life. The LED driver specification determines whether dimming is supported. Dimensions × × × 🔍 Dimensions — tap to enlarge Stretch Fabric Flush Mount Specs Light source Integrated SMD LED panel · pre-installed · no bulb required Color temperature CONFIRM BEFORE PUBLISHING — confirm with supplier spec sheet Wattage Small (Ø40 cm): 22WMedium (Ø50 cm): 32WLarge (Ø60 cm): 48W Sizes Small: Ø40 × H15 cm (15.7″ × 5.9″)Medium: Ø50 × H15 cm (19.7″ × 5.9″)Large: Ø60 × H15 cm (23.6″ × 5.9″) Color / finish Off-white stretch fabric · solid walnut center cap · brass-tone hardware (single colorway) Material Stretch fabric shade · solid wood (walnut) center cap · metal hardware frame Room coverage 10–18 m² (108–194 sq ft) — varies by size Mounting Flush mount · hardwired to ceiling junction box · H15 cm (no drop) Input voltage CONFIRM BEFORE PUBLISHING — confirm 110–240V or 220–240V IP rating IP20 — indoor, dry locations only (confirm with supplier) Dimmable CONFIRM BEFORE PUBLISHING — depends on LED driver specification LED lifespan ~25,000+ hours (confirm with supplier) Best for Bedroom · living room · dining area · study · hallway · Japandi · organic modern · transitional · warm-neutral interiors with standard ceiling heights Default configuration Select size at checkout. Integrated LED panel included (22W / 32W / 48W) — no separate light source required. Single colorway: walnut + off-white fabric. Email us for trade or bulk pricing. Installation & Care Turn off power at the breaker before installation. A licensed electrician is recommended for all hardwired ceiling connections. Flush mount fixtures install directly to the junction box — confirm the box position suits the room layout before hardwiring, as the fixture cannot be repositioned afterward. The integrated LED panel is pre-installed — no bulb assembly is required. After installation, restore power at the breaker and the fixture is ready to use. If the fixture is dimmable (confirm with spec sheet): use a compatible leading- or trailing-edge LED dimmer switch. Connecting a non-dimmable driver to a dimmer circuit may cause flickering or driver damage. Stretch fabric shade: dust with a soft brush or low-suction vacuum brush attachment. Do not wet-clean, iron, or steam — heat and moisture can distort the tension folds and alter the way the fabric sits across the frame. Avoid installing in high-humidity zones unless IP rating is confirmed. Solid walnut center cap: wipe with a dry cloth only. Avoid water and oil-based polish, which can darken or strip the wood finish. Brass-tone hardware fastener: dry cloth only. Metal frame: dry microfiber cloth. Avoid liquid cleaners and abrasive pads. Downloads & Resources Spec Sheet FAQs Does it need a bulb? No. An integrated SMD LED panel ships pre-installed inside the fixture (22W for Ø40 cm, 32W for Ø50 cm, and 48W for Ø60 cm) — there is no socket and no separate bulb to purchase or install. Hardwire to the ceiling junction box and restore power at the breaker; the light is ready immediately. rated lifespan is typically 25,000+ hours under normal use conditions, which at 6 hours daily use is approximately 11+ years. Which size should I choose? The Small (Ø40 cm, 22W) suits a bedroom, study, or hallway in a 10–13 m² space — it provides centered overhead light without visually dominating a smaller room. The Medium (Ø50 cm, 32W) works as the primary ceiling light in a 13–16 m² bedroom or dining area. The Large (Ø60 cm, 48W) anchors a 16–18 m² living room, primary bedroom, or open dining space. All three sizes share the same H15 cm profile, so the visual depth in the room is consistent regardless of size; only the spread of light and the decorative footprint change. Is it dimmable? Dimming depends on the internal LED driver specification. Confirm dimmability with the supplier spec sheet before connecting to a wall dimmer switch. If the driver supports Triac (leading-edge) or trailing-edge dimming, use a compatible LED dimmer — do not use a standard incandescent dimmer. Connecting a non-dimmable driver to a dimmer circuit can cause flickering, buzzing, or driver damage over time. What does the "stretch fabric" look like in person? The fabric is an off-white stretch material pulled over a segmented petal frame. When installed and unlit, it looks like a softly pleated dome with natural gather lines radiating from the walnut center cap outward — similar in texture to gathered linen or a stretched canvas, with variation in how the folds catch ambient light. When lit from behind by the LED panel, the fabric glows evenly from within, and the fold lines appear as gentle shadows across the lit surface. It does not have a printed pattern — the texture comes entirely from the physical tension and gather of the material. Will this work in a standard 8-foot ceiling room? Yes. At H15 cm (5.9″) the fixture sits flush against the ceiling with no pendant drop, making it well-suited for standard 2.4 m (8 ft) residential ceilings. The bottom of the fixture will sit at ceiling height minus 15 cm — in a room with a 2.4 m ceiling and a typical dining table at 75 cm height, there is ample clearance beneath the fixture for all three sizes. What interior styles does this suit? The off-white fabric, solid walnut center, and brass-tone detail work naturally in Japandi, organic modern, and transitional interiors that use warm neutrals, natural wood furniture, and soft textile surfaces. The petal silhouette has enough visual character to be a design element in a room, rather than just a functional overhead light. It does not suit industrial, high-gloss contemporary, or cool-palette interiors where the warm fabric and walnut would read as out of place.   Sizing & questions Every piece is made to order in our own atelier — here is what most clients ask before choosing theirs. Which size should I choose for my bedroom or living room?+Small (Ø 15.7″) covers 108–140 sq ft bedrooms and compact spaces. Medium (Ø 19.7″) suits 140–172 sq ft bedrooms, dining areas, and open studies. Large (Ø 23.6″) works best in 172–194 sq ft living rooms, dining rooms, and open-plan primary bedrooms. Will this fixture work in a standard 8 ft ceiling?+Yes. At H 5.9″, the Petal Flush Mount sits close to the ceiling and is designed specifically for standard 2.4 m (8 ft) rooms without requiring any drop from the ceiling. Do I need to buy a light bulb separately?+No. The fixture includes an integrated LED panel pre-installed and ready to use. Simply hardwire to your ceiling box and turn on power at the breaker—no separate bulb purchase needed. How is this fixture installed?+It hardwires directly to your ceiling junction box as a flush mount. A licensed electrician is recommended. Turn off power at the breaker before installation and confirm the ceiling box location, as the fixture cannot be repositioned after hardwiring. Can I order a custom size?+The Petal Flush Mount is available in three fixed sizes. For custom dimensions or other modifications, contact Vakkerlight atelier to discuss made-to-order options tailored to your space.