Adjustable Travertine Dome Vanity Light

A closer fit for your
everyday comfort.

An adjustable travertine dome vanity light — hand-carved natural-travertine dome shades on a walnut-wood backplate, each head on a black swivel joint you can angle where the light is needed. Available in 2, 3, and 4-head bars from 12.6″ to 27.6″ wide. Integrated LED, 5W per head. For bathroom vanities, mirrors, hallways, and as directional wall accent lighting. Features Adjustable swivel heads Each travertine dome tilts and rotates on a black joint — aim light at a mirror, artwork, or down a hallway. Natural travertine domes Hand-carved stone with open pores and color banding — every dome reads slightly differently. Walnut backplate · integrated LED Real walnut-wood bar with 5W integrated LED per head, 2700K warm white. AC 110–240V. Configuration Options Head count 2, 3, or 4 adjustable travertine domes on a single walnut bar. Mounting direction Mounts horizontally above a mirror, or vertically beside one. Heads aim either way. Default configuration Pictured: walnut-wood backplate, natural travertine domes, black swivel joints. Heads ship centered and are aimed on installation. Custom finish Backplate: walnut wood (default) or natural oak. Joint hardware: matte black (default) or brushed brass. Email us to confirm finishes before ordering. Sizes & Configurations Heads Width Projection Metric (W × D × H) Wattage Lumens 2-head 12.6″ 6.7″ off wall 32 × 6 × 17 cm 18W 1260 lm 3-head 20.1″ 6.7″ off wall 51 × 6 × 17 cm 27W 1890 lm 4-head 27.6″ 6.7″ off wall 70 × 6 × 17 cm 36W 2520 lm Shape Diagrams Click any diagram to enlarge. Click to enlarge ↗ Specifications Material Natural travertine domes · walnut-wood backplate · black metal joints Sizes 2-head 12.6″ · 3-head 20.1″ · 4-head 27.6″ — see Sizes table Projection 6.7″ (17 cm) off the wall Light source Integrated LED · 5W per head · 2700K warm white · dimmable Total wattage / lumens 2-head: 18W / 1260 lm · 3-head: 27W / 1890 lm · 4-head: 36W / 2520 lm LED service LED replaceable at authorized service Voltage AC 110–240V (universal) Adjustability Each head tilts and swivels on a black joint Mounting Hardwired wall mount, horizontal or vertical Moisture rating IP20 — indoor, dry locations only Backplate finish Walnut wood (default); natural oak on request Stone finish Natural travertine, hand-carved (open pores and color banding vary by piece) Control Compatible with common dimmers (not included) Certification Listed · North America · CE · SAA · SASO · KC Installation Notes Hardwired wall install — a licensed electrician is recommended. Mounts horizontally above a mirror or vertically beside one. Mount over a standard wall junction box; the walnut backplate covers the box. Confirm box position against the bar length before install. Each head tilts and swivels — aim the domes after mounting to light a mirror, a vanity, or graze a textured wall. Travertine is a porous natural stone — open cavities, surface pitting, and color banding are core characteristics of the material, not flaws or damage. No two domes are identical. The walnut backplate is real wood — grain pattern and tone vary by piece, and the photograph shows a representative sample. Indoor dry locations only (IP20). For a bathroom, mount well clear of the shower or tub spray zone — travertine is porous and absorbs moisture, and the LED is not wet-rated. Downloads & Resources Spec Sheet Request 3D Files FAQs Can I really aim each head? How far do they move? Yes — each travertine dome sits on a black swivel joint that both tilts up and down and rotates side to side, so you can point light at a mirror, wash it down a wall, or angle it onto artwork. Aim the heads after the bar is mounted; they hold their position once set. Which size fits my mirror or vanity? As a rule of thumb, pick a bar about 75% of your mirror width. 2-head (12.6″) suits a small mirror or powder room; 3-head (20.1″) suits a standard 24–30″ vanity; 4-head (27.6″) suits a 36″+ vanity or a double sink. Email us your mirror width if you're unsure. Can I install it in a bathroom? Yes, on a vanity wall clear of direct water. It's rated IP20 for indoor dry locations — fine above a mirror or sink, but keep it out of the shower or tub spray zone. Travertine is porous and absorbs moisture, which stains the stone over time, so it isn't suited to a wet zone. The travertine domes have holes and pits — is that a defect? No — those are natural to travertine. Open cavities, surface pitting, and color banding are core characteristics of the stone, not flaws or shipping damage. Each dome is hand-carved, so no two are exactly alike; that variation is the point of a natural-stone fixture. What's the LED lifespan, and what happens when it fails? Each head has a 5W integrated LED rated over 30,000 hours — roughly 25 years at 3 hours of daily use. If a head fails within or after the warranty period, contact authorized service with your order number for a replacement LED module rather than replacing the whole fixture. Sizing & questions Every piece is made to order in our own atelier — here is what most clients ask before choosing theirs. What sizes are available?+Three configurations: 2-head at 12.6″ wide, 3-head at 20.1″ wide, or 4-head at 27.6″ wide. Each projects 6.7″ from the wall. Custom sizing available—contact our atelier to discuss your vanity width. Can I aim the heads in different directions?+Yes. Each travertine dome tilts and swivels on a black joint, allowing you to angle light at the mirror, vanity, or down a hallway. Heads arrive centered and are aimed on installation. What finishes are offered?+Walnut-wood backplate (default) with natural travertine domes and matte black swivel joints. Natural oak backplate and brushed brass joints available on request—email to confirm before ordering. Can I dim this light?+Yes. The integrated LED is compatible with common dimmers (not included). Specify dimmable control when ordering. How is it installed?+Hardwired wall mount, horizontal above a mirror or vertical beside one. A licensed electrician is recommended. Mounts over a standard junction box; the walnut backplate covers it. Confirm box position against bar length first.